 |
 |
|
|
|
|
|
 |
|
|
|
|
|
|
|
|
|
|
- Balanced Drive motor structure for optimal drive force symmetry resulting in largely reduced even order harmonic distortion
- Copper cap on center pole to reduce voice coil inductance and to minimize variations in voice coil inductance as a function of voice coil position
- Black coated semi-air-dried paper cone
- Rigid die cast alu chassis with extensive venting for lower air flow speed reducing audible distortion
- Vented voice coil former for reduced distortion and compression
- Vented center pole with dual flares for reduced noise level at large cone excursions
- Heavy-duty black fiber glass voice coil former to reduce mechanical losses resulting in better dynamic performance and low-level details
- Large motor with 1.25” voice coil diameter for better control and power handling
- Built-in alu field-stabilizing ring for reduced distortion at high levels
- Low-loss suspension (high Qm) for better reproduction of details and dynamics
- Black motor parts for better heat transfer to the surrounding air
- Conex spider for better durability under extreme conditions
- Gold plated terminals to ensure long-term trouble free connection
|
|
|
|
FREQUENCY RESPONSE
|
|
|
|
NOMINAL SPECIFICATIONS
|
|
|
|
|
Notes
|
Parameter
|
WF152BD03
|
WF152BD04
|
Unit
|
|
Before burn-in
|
After burn-in
|
Before burn-in
|
After burn-in
|
|
|
Nominal size
|
6
|
6
|
[inch.]
|
|
|
Nominal impedance
|
4
|
8
|
[ohm]
|
|
|
Recommended max. upper frequency limit
|
3.5
|
3.5
|
[kHz]
|
|
1
|
Sensitivity, 2.83V/1m (average SPL in range 300 - 1,000 Hz)
|
91
|
88.5
|
[dB]
|
|
2
|
Power handling, short term, IEC 268-5, no additional filtering
|
120
|
120
|
[W]
|
|
2
|
Power handling, long term, IEC 268-5, no additional filtering
|
110
|
110
|
[W]
|
|
2
|
Power handling, continuous, IEC 268-5, no additional filtering
|
70
|
70
|
[W]
|
|
|
Effective radiating area, Sd
|
93
|
93
|
[sq.cm]
|
|
3, 6
|
Resonance frequency (free air, no baffle), Fs
|
55.5
|
50
|
56.5
|
51
|
[Hz]
|
|
|
Moving mass, incl. air (free air, no baffle), Mms
|
11.0
|
10.6
|
[g]
|
|
3
|
Force factor, Bxl
|
5.8
|
7.3
|
[N/A]
|
|
3, 6
|
Suspension compliance, Cms
|
0.75
|
0.93
|
0.75
|
0.93
|
[mm/N]
|
|
3, 6
|
Equivalent air volume, Vas
|
9.2
|
11.4
|
9.2
|
11.4
|
[lit.]
|
|
3, 6
|
Mechanical resistance, Rms
|
0.43
|
0.46
|
0.43
|
0.46
|
[Ns/m]
|
|
3, 6
|
Mechanical Q, Qms
|
8.9
|
7.5
|
8.7
|
7.3
|
[-]
|
|
3, 6
|
Electrical Q, Qes
|
0.36
|
0.33
|
0.44
|
0.40
|
[-]
|
|
3, 6
|
Total Q, Qts
|
0.35
|
0.31
|
0.42
|
0.38
|
[-]
|
|
4
|
Voice coil resistance, RDC
|
3.2
|
6.3
|
[ohm]
|
|
5
|
Voice coil inductance, Le (measured at 10 kHz)
|
0.096
|
0.15
|
[mH]
|
|
|
Voice coil inside diameter
|
32
|
32
|
[mm]
|
|
|
Voice coil winding height
|
14
|
14
|
[mm]
|
|
|
Air gap height
|
5
|
5
|
[mm]
|
|
|
Magnet weight
|
630
|
630
|
[g]
|
|
|
Total unit net weight excl. packaging
|
1.65
|
1.65
|
[kg]
|
|
3, 5
|
Krm
|
46
|
50
|
[mohm]
|
|
3, 5
|
Erm
|
0.39
|
0.42
|
[-]
|
|
3, 5
|
Kxm
|
260
|
580
|
[mH]
|
|
3, 5
|
Exm
|
0.16
|
0.12
|
[-]
|
|
|
|
|
|
Note 1
|
Measured in infinite baffle.
|
|
Note 2
|
Tested in free air (no cabinet).
|
|
Note 3
|
Measured using a semi-constant current source, nominal level 2 mA.
|
|
Note 4
|
Measured at 20 deg. C
|
|
Note 5
|
It is generally a rough simplification to assume that loudspeaker transducer voice coils exhibit the characteristics of an inductor. Instead it is a far more accurate approach to use the more advanced model often referred to as the “Wright empirical model”, also used in LEAP-4 as the TSL model (www.linearx.com), involving parameters Krm, Erm, Kxm, and Exm. This more accurate transducer model is described in a technical paper (PDF) here.
|
|
Note 6
|
After burn-in specifications are measured 12 hours after exiting the transducer by a 20 Hz sine wave for 2 hours at level 10/14.1 VRMS (4/8 ohm version). The unit is not burned in before shipping.
|
|
|
|
|
HARMONIC DISTORTION
|
|
|
|
OUTLINE DRAWING AND NOMINAL DIMENSIONS (mm)
|
|
|
|
|
|
TERMINAL NOMINAL DIMENSIONS (mm)
|
|
|
|
PACKAGING AND ORDERING INFORMATION
|
|
|
|
|
Part no. WF152BD03-01
|
4 ohm version, individual packaging (one piece per box)
|
|
Part no. WF152BD03-02
|
4 ohm version, bulk packaging
|
|
Part no. WF152BD04-01
|
8 ohm version, individual packaging (one piece per box)
|
|
Part no. WF152BD04-02
|
8 ohm version, bulk packaging
|
|
|
|
|
Latest update: Mar. 1, 2021
|
|
|
|
|
|
|
|
Specifications are subject to change without any further notice.
Copyright © 2006-2023 by Wavecor Ltd., China. All rights reserved.
|
|
|
|
|
|
MORE INFO
|
|
|
|
|
|
