 |
 |
|
|
|
|
|
 |
|
|
|
|
|
|
|
|
|
|
- Vented voice coil former and magnet center pole for reduced distortion and compression
- Vented chassis for lower air flow speed reducing audible distortion
- Voice coil wound with Copper Clad Aluminium Wire for higher efficiency and better dynamics
- Heavy-duty black fiber glass voice coil bobbin to increase power handling and reduce mechanical losses resulting in better dynamic performance and low-level details
- Low-loss suspension (high Qm) for better reproduction of details and dynamics
- Black magnet parts for better heat transfer to increase power handling
- Progressive suspension with specially designed CONEX damper (spider) for long durability under extreme operating conditions
- Gold plated terminals to prevent oxidation for long-term reliable connection
- Delivered with foam gasket attached for hassle-free mounting and secure cabinet sealing
|
|
|
|
|
|
FREQUENCY RESPONSE
|
|
|
|
|
|
|
|
|
Downloads
SPL and impedance response curves as text files
|
|
|
|
WF090WA01 on-axis SPL response
|
|
WF090WA01 impedance response
|
|
|
WF090WA02 on-axis SPL response
|
|
WF090WA02 impedance response
|
|
|
|
|
Important!
Please observe that these text files for download are actual measurements of the drivers measured in infinite baffle and without any enclosure. Measuring the drivers in a finite baffle (like the baffle of most speaker cabinets) and in any size of enclosure will lead to different response curves.
|
|
|
|
|
NOMINAL SPECIFICATIONS
|
|
|
|
|
|
Notes
|
Parameter
|
WF090WA01
|
WF090WA02
|
Unit
|
|
Before burn-in
|
After burn-in
|
Before burn-in
|
After burn-in
|
|
|
Nominal size
|
3.5
|
3.5
|
[inch.]
|
|
|
Nominal impedance
|
4
|
8
|
[ohm]
|
|
|
Recommended max. upper frequency limit
|
5
|
5
|
[kHz]
|
|
1, 5
|
Sensitivity, 2.83V/1m (average SPL in range 300 - 4,000 Hz)
|
86.5
|
84
|
[dB]
|
|
2
|
Power handling, short term, IEC 268-5, no additional filtering
|
30
|
30
|
[W]
|
|
2
|
Power handling, long term, IEC 268-5, no additional filtering
|
15
|
15
|
[W]
|
|
2
|
Power handling, continuous, IEC 268-5, no additional filtering
|
8
|
8
|
[W]
|
|
|
Effective radiating area, Sd
|
36
|
36
|
[sq.cm]
|
|
3, 5, 7
|
Resonance frequency (free air, no baffle), Fs
|
115
|
109
|
117
|
110
|
[Hz]
|
|
|
Moving mass, incl. air (free air, no baffle), Mms
|
3.45
|
3.35
|
[g]
|
|
3
|
Force factor, Bxl
|
2.9
|
3.5
|
[N/A]
|
|
3, 5, 7
|
Suspension compliance, Cms
|
0.55
|
0.62
|
0.55
|
0.62
|
[mm/N]
|
|
3, 5, 7
|
Equivalent air volume, Vas
|
1.02
|
1.14
|
1.02
|
1.14
|
[lit.]
|
|
3, 5, 7
|
Mechanical resistance, Rms
|
0.39
|
0.39
|
0.39
|
0.39
|
[Ns/m]
|
|
3, 5, 7
|
Mechanical Q, Qms
|
6.4
|
6.1
|
6.3
|
6.0
|
[-]
|
|
3, 5, 7
|
Electrical Q, Qes
|
0.92
|
0.87
|
1.11
|
1.04
|
[-]
|
|
3, 5, 7
|
Total Q, Qts
|
0.81
|
0.76
|
0.94
|
0.89
|
[-]
|
|
4
|
Voice coil resistance, RDC
|
3.1
|
5.5
|
[ohm]
|
|
6
|
Voice coil inductance, Le (measured at 10 kHz)
|
0.14
|
0.22
|
[mH]
|
|
|
Voice coil inside diameter
|
22
|
22
|
[mm]
|
|
|
Voice coil winding height
|
8.5
|
8.5
|
[mm]
|
|
|
Air gap height
|
3
|
3
|
[mm]
|
|
|
Theoretical linear motor stroke, Xmax
|
+/-2.75
|
+/-2.75
|
[mm]
|
|
|
Magnet weight
|
135
|
135
|
[g]
|
|
|
Total unit net weight excl. packaging
|
0.34
|
0.34
|
[kg]
|
|
3, 6
|
Krm
|
|
|
[mohm]
|
|
3, 6
|
Erm
|
|
|
[-]
|
|
3, 6
|
Kxm
|
|
|
[mH]
|
|
3, 6
|
Exm
|
|
|
[-]
|
|
|
|
|
|
Note 1
|
Measured in infinite baffle.
|
|
Note 2
|
Tested in free air (no cabinet).
|
|
Note 3
|
Measured using a semi-constant current source, nominal level 2 mA.
|
|
Note 4
|
Measured at 20 deg. C
|
|
Note 5
|
Measured at 25 deg. C
|
|
Note 6
|
It is generally a rough simplification to assume that loudspeaker transducer voice coils exhibit the characteristics of an inductor. Instead it is a far more accurate approach to use the more advanced model often referred to as the “Wright empirical model”, also used in LEAP-4 as the TSL model (www.linearx.com), involving parameters Krm, Erm, Kxm, and Exm. This more accurate transducer model is described in a technical paper (PDF) here.
|
|
Note 7
|
After-burn-in specifications are measured at least 12 hours after exiting the transducer by a 20 Hz sine wave for 2 hours at level 2.83/4.0 VRMS (4/8 ohm version). Unit are not burned in before shipping.
|
|
|
|
|
OUTLINE DRAWING AND NOMINAL DIMENSIONS (mm)
|
|
|
|
|
|
TERMINAL NOMINAL DIMENSIONS (mm)
|
|
|
|
PACKAGING AND ORDERING INFORMATION
|
|
|
|
|
Part no. WF090WA01-01
|
4 ohm version, individual packaging (one pair per box)
|
|
Part no. WF090WA01-02
|
4 ohm version, bulk packaging
|
|
Part no. WF090WA02-01
|
8 ohm version, individual packaging (one pair per box)
|
|
Part no. WF090WA02-02
|
8 ohm version, bulk packaging
|
|
|
|
|
Latest update: March 1, 2024
|
|
|
|
|
|
|
|
|
Specifications are subject to change without any further notice.
Copyright © by Wavecor Ltd., China. All rights reserved.
|
|
|
|
|
|
MORE INFO
|
|
|
|
|
|
